Reloading your own ammunition comes down to the same few steps for every cartridge: clean the brass, resize it and knock out the spent primer, prepare the case, seat a new primer, add a measured powder charge, and seat a bullet. Each step has a tool. This checklist walks through them in order — what each one does, what to look for, and which ones you can skip at first.
Before anything else: get a current load manual. Every powder charge you use should come from a published manual from a bullet or powder manufacturer, for your exact bullet, powder and primer. Never guess, and never use data you can’t trace to a published source.
1. A reloading press
The press is the frame everything else mounts to. Dies thread into the top; the shell holder on the ram holds the case.
- Single-stage press: one die at a time, one case at a time. Slower, but simple, very rigid, and the best way to learn. Most reloaders keep one even after they upgrade.
- Turret press: holds several dies at once and rotates between them, so you don’t swap dies for every step. A good middle ground for pistol and small-batch rifle loading.
- Starter kits: a press plus most of the bench tools in one box — usually the simplest way to start.
2. Dies and shell holders
Dies are cartridge-specific. A die set resizes the case, removes the spent primer, and seats the bullet; some sets also crimp.
- Rifle die sets are usually two dies (full-length size/decap, and seat). Examples: RCBS Full Length Die Set, 6.5 Creedmoor, Hornady 2-Die Set, 300 Blackout, Hornady Series III 2-Die Set, 6mm ARC.
- Shell holders hold the case head in the press ram. Each one fits a family of cartridges by number — check your die maker’s chart for the right number for your cartridge.
- Singles: RCBS #3, RCBS #14, RCBS #16, Hornady #1, Hornady #16
- Set: Hornady Shell Holder Kit (#1, #2, #5, #16)
- Die lock rings keep your die adjustment from drifting: Frankford Arsenal Die Locker Rings (7/8×14)
3. Brass cleaning: tumbler and media
Clean brass is easier on your dies and easier to inspect for cracks and damage.
- Vibratory tumblers use dry media (like ground walnut) and are simple and low-maintenance. Hornady M-1 Case Tumbler · Frankford Arsenal Quick-n-EZ Case Tumbler Kit · Ground Walnut Media, 5 lb
- Rotary (wet) tumblers use water, solution and usually stainless pins, and clean inside the case and primer pocket. Frankford Arsenal Rotary Tumbler · Frankford Arsenal Tumbler Pro Kit
- Ultrasonic cleaners use cleaning solution and sound waves: Frankford Arsenal Ultrasonic Brass Cleaning Solution, 32 oz
4. Case prep: depriming, trimming, measuring
- Depriming: most sizing dies remove spent primers, but a separate depriming tool lets you knock primers out before wet tumbling so the pockets get clean too. Keep spare decapping pins — they’re the part that breaks.
- Trimming: brass stretches when it’s fired and resized. Cases that grow past the maximum length in your load manual need trimming back.
- Measuring: a caliper checks case length and finished cartridge length against your manual. Hornady Digital Caliper
5. Priming
Seating a new primer can be done on the press or by hand. A hand priming tool gives good feel for primer seating depth and lets you prime away from the bench.
6. Powder: scale, measure, trickler
This is the step where accuracy matters most.
- Scale: every charge is checked against a scale. A digital bench scale is the most common starting point; keep its calibration weights and check it every session.
- Powder measure: throws a repeatable volume of powder so you’re not spooning every charge. Verify thrown charges on the scale. Hornady Lock-N-Load Powder Measure
- Trickler: adds powder a few kernels at a time to bring a charge up to exact weight. Hornady Powder Trickler
- Automated dispenser: weighs and dispenses each charge for you — faster for precision rifle loading. Hornady Auto Charge Pro
7. Bench organization
- Loading block: holds cases upright between steps so you can see every case has been charged — and that none has been charged twice. RCBS Universal Case Loading Block
- Labels: record what’s in every box. Frankford Arsenal Reloader Labels (100 pk)
8. Components
Once the bench is set up, you need the consumables: brass, primers, powder and bullets — each matched to your load manual. Browse them in Reloading Supplies and Bullets & Projectiles.
Quick checklist
| Step | Must-have | Nice to have |
|---|---|---|
| Load data | Published load manual | A second manual to cross-check |
| Press | Single-stage or turret press (or a kit) | — |
| Dies | Die set + correct shell holder | Die lock rings |
| Cleaning | Tumbler + media | Wet/ultrasonic for primer pockets |
| Case prep | Caliper, trimmer | Separate depriming tool, pocket brush |
| Priming | Hand primer or press priming | — |
| Powder | Scale + calibration weights | Powder measure, trickler, auto dispenser |
| Bench | Loading block, labels | — |
Reloading involves explosive components. Follow the safety guidance in your load manual and every manufacturer’s instructions, and use only published load data.